|
| |
This mold will produce the finest votive candles, which will fit into all popular votive containers. The finished candles may be used as room scenters, food warmers and patio lights. These molds are made from heavy seamless metal and taper from top to bottom. Top is 1 3/4 '', bottom 1 1/2 '', height 2''. This taper insures easy removal of finished candle from mold. Slightly flared at top.
SKU Number: Met Vot Mold
|
|
|
|
|
| |
Three tin plate round votive molds "welded" to a metal strip for easy handling. Each round votive mold cup is 1-9/16" in diameter by 2" high.
SKU Number: Rnd Vot Mld 3
|
|
|
|
|
| |
Three tin plate square votive molds "welded" to a metal strip for easy handling. Each square tapered votive mold is 1 3/4 " by 1 3/4 " by 2" tall.
SKU Number: Sqr Vot Mld 3
|
|
|
|
|
| |
This unique tool allows you to shave wax from either end of your tapered candles. Reduce the diameter of the candle base or reshape the top of a used taper to restore its beauty.
SKU Number: Candle Shap
|
|
|
|
|
| |
A flexible one foot length of 1/4 '' diameter lead. Used to "weight" metal molds in water bath. Simply wrap the length of lead around the base of the mold.
SKU Number: Mld Wght
|
|
|
|
|
| |
Candles made in this mold can be used to float on water as in a centerpiece, party favors or as wax embedments in larger candles. The molds are seamless and made from heavy gauge tin plate with scalloped edges. They measure 3/4 " deep, 2 1/4 " across top & 1 3/8" across the bottom. Also available in 3-cup and 6-cup strips.
SKU Number: Tart Mld
|
|
|
|
|
| |
These round wick tabs are used to secure wick to bottom of containers or votives. Has been the industry standard for years. It is 15mm in diameter, about the size of dime, with a 3-mm neck. Approximately 1100 tabs per pound.
SKU Number: Wck Tabs 15mm
|
|
|
|
|
| |
These round wick tabs are used to secure wick to bottom of medium to large size container candles. Can also be used for pillars and votives. It is 20mm in diameter, about the size of a nickel, with a 3-mm neck. Approximately 660 tabs per pound.
SKU Number: Wck Tabs 20mm
|
|
|
|
|
| |
These magnetic mold sealers are a lifesaver for the candle maker. Simply thread wick tip through wick hole leaving approximately 1/2 " exposed. Bend this end so that it lies flat and attach magnetic mold sealer making sure the wick is not exposed. Apply pressure to ensure a good seal. Be sure to watch your wax temperature. Wax that is poured too hot may loosen seal. Wipe clean after each use. Available in packs of 6 pieces.
SKU Number: Mag Mld Seal
|
|
|
|
|
| |
Our votive wick pins fit perfectly into our standard 2 oz votive molds. Just place the wick pin in the votive mold, pour your wax and let set up. When the votive comes out of the mold, simply push the wick pin out and replace with your tabbed wick. These wick pins save a tremendous amount of time and effort and as an added bonus, the wicks are always perfectly aligned.
SKU Number: VotWicPins
|
|
|
|
|
| |
A set of 12 - 2 oz standard size seamless metal votive molds with 12 votive wick pins.
SKU Number: VotMldWicPinSet
|
|
|
|
|
| |
These 3/4" wide metal wick bars can be used to hold wick in place in jars as well as candle molds. Available in 4", 5", 6" and 7" lengths and packaged in lots of 6.
SKU Number: MtlWicBars
|
|
|
|
|
| |
These molds are used to make wax tarts, chunks or scent samplers. These molds are made of crystal-clear resilient PVC plastic and can accommodate high fragrance loads and pour temps up to 175 degrees F. Can also be used to make scented soap cubes. Each clamshell unit will hold 2.4 ounces of wax (for all 6 melts) and each cube produced is 1 inch in diameter.
SKU Number: TartClamshell
|
|
|
|
|
| |
These are tapered rubber plugs used to seal the bottom of aluminum and tin-plate metal candle molds. Just fasten wick to top of mold with craft stick or suitable wick bar; pull tight at base and push & twist small end of rubber plug into hole to prevent wax from leaking out of wick hole.
SKU Number: RubberPlugs
|
|
|
|
|
| |
These molds are used to make wax tarts, chunks or scent samplers. These molds are made of crystal-clear resilient PVC plastic and can accommodate high fragrance loads and pour temps up to 175 degrees F. Can also be used to make scented soap cubes. Each clamshell unit will hold 5 ounces of wax (for all 6 melts) and each cube produced is 1-1/2 X 1-1/2 X 7/8 inch in diameter.
SKU Number: TartClamshell
|
|
|
|
|
| |
20 mm size candle wick stickers for use in attaching wick tab assemblies to containers. Available in 100's, 500's, and 1000's.
SKU Number: Cand Wick Stick
|
|
|
|
 "Metal Votive Molds")
 "Round Votive Mold (3-In-1 Strip)")
 "Square Votive (3-In-1 Strip)")
 "Candle Shaper")
 "Mold Weight")
 "Floater/Tart Candle Mold")
 "Round Wick Tabs (15mm)")
 "Round Wick Tabs (20mm)")
 "Magnetic Mold Sealer")
 "Votive Wick Pins")
 "Votive Mold/Wick Pin Set")
 "Metal Wick Bars")
 "Wax Tart Melt Clamshell Molds - STANDARD SIZE")
 "Rubber Plugs For Sealing Wick Holes")
 "Wax Tart Melt Clamshell Molds - JUMBO SIZE")
 "Candle Wick Stickers")
